Buying Guide

How to Install Your Fish Finder?

Install your Fish Finder

Setting up the fish finder the way in which is correct will guarantee you will get the most benefit from it. Enjoying just a little extra time and energy to get the job done precisely will certainly result in lots of pleasant fishing trips.

Step 1: determine how you can mount the transducer

This may be just about the most crucial & most delicate stage of the installing. The majority of devices include a transom mount which you are able to easily set up in your own home using tools available in the garage area of your house. At any time you plumped for a thru-hull device transducer, I suggest you ensure it is completed professionally because the installation is much more complex and requires drilling/cutting a hole through the base of your own boat.

Quite a few people recommend looking for a spot for your own personal fish finder initially, suggesting that you should find out how you can operate the wires. It’s a lot handier to start with by installing the transducer and then figure out how long the wires lead. You’ll be able to shift the fish finder device around, however, your transducer needs to be along the transom.

Have a look at the hull to figure out a spot that will definitely remain submerged in water. The transducer needs to be and preferably submerged with the water always or else it will not work. It’s also wise to consider exactly how sleek or smooth that area of the transom is, how much out from the propeller it is, in case there’s anything at all close by that could disrupt the flowing of water. The greater the turbulence you can find, the greater the disruption you’ll encounter reading.

It’s also wise to give consideration to where in fact the location of your transducer is likely to be once your motorboat /boat is actually trailered. Ensure that it is positioned in a manner that it does not get knocked /bumped over. Ensure that the transducer lies absolutely horizontal.

Step 2: Testing the wires

Prior to basically attach the transducer in, it is best that you test and examine the wires that rest from it in the direction of the primary unit and out from the primary device towards the battery. In case you did it just after screwing it stuck, an unintentional pull on the wire could cause the sealer we’re going to apply in order to seal the gaps to weaken or even loosen.

Provided your cables are a bit long, you shouldn’t cut them. Cutting wires in whatever way will certainly VOID your product warranty. Alternatively, secure the wiring or tighten all of them with ties, close to the primary unit and never close to the transducer.

WARNING: You shouldn’t operate the transducer cable together with the engine’s electrical circuitry funnel or even the VHF cable because this trigger disturbance that can screw up the fish finder’s overall performance.

Step 3: How to mount the transducer

As soon as you have located a great spot, put a plastic material block onto it. You’ll be able to attach the transducer to this block, to ensure you do not need to drill any kind of unwanted holes in the boat. Let sufficient time for block’s adhesive or epoxy to dry out and stick firmly. Put the transducer on the block as discussed above and label the gaps with a pen. That’s the place where you’ll end up drilling.

If you would like to secure the transducer straight on the transom then you need to mark both the holes, as well as drill thru them. Attach with screws the transducer by using the mounting components that can be found in the box, and apply a substantial quantity of silicone sealer on each hole, don’t forget to apply plenty of seal inside and plenty outside also. This is going to make certain that no water/liquid will escape through from anyplace because that would cause a great deal of problem.

Even when you are working with a plastic block, it is often a good idea to apply sealant, in the event that the holes you drilled affected the transom or if perhaps you made a gap in it.

Step 4: How to run the actual wires

You now understand how to run the wires, therefore it is the perfect time to perform the actual running. You will find two methods to perform this: decide either to start over the transom, or through the gap in the transom. Ensure that at any time you drill down a hole in your transom, its High ABOVE the waterline.

It is best that you lock in the cable simply by clamps/tie each and every about eighteen inches approximately. When you do this, they’re going to stay and won’t move around very much.

You’ll also need to run the cables out from the power source towards primary unit. More and more manufacturer’s wires include an electrical fuse integrated. You should never remove the fuse. A sudden power rise can destroy your device. If there is not a fuse available, it is wise to install one. Keep in mind when establishing a connection to the power source that the red is always positive and therefore black is always negative.

Remember to keep the terminals disconnected while you finish your installation. You’ll be able to tighten them using any type of connectors you consider easier.

Step 5: How to mount your fish finder

At this point, you need to have a mounted transducer and wires flowing out from the transducer towards your preferred place for the fish finder, as well as from the power source towards your fish finder location.

Provided your boat features an instrument panel/dashboard, many fish finders own so called in-dash mounts that are offered apart and you can utilize. Mark the spot on your dashboard with a pen or pencil, and slice it out cautiously. In the event that you cut out far too much, you will not be capable of repairing it. Nearly all manuals include very simple guidelines to construct and restore fish finder mounts.

Step 6: Last step is to enjoy.

As soon as all the details are fixed as well as your sealant did get plenty of time to dry, it is the perfect time to bring your boat on the water. Supposing that you did every little thing precisely and also the transducer is mounted correctly, you should begin receiving readings immediately.

Right now it is your responsibility to adjust and modify the configurations to ensure you get the very finest overall performance depending on your personal style and also your needs.